Versions Compared

Version Old Version 10 New Version 11
Changes made by

Aleeshya Broome

Aleeshya Broome

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Anchor
Top
Top

This page explains the process to identify and touch up concern areas on an installed system. All system components should be inspected throughout the installation of the system. With any touch ups completed, ensure the final result is not visible to the naked eye, and blends properly with the material.

Page Contents

Skill Requirements
Tools & Hardware
Process Steps
Related Training Materials
Final Steps & Delivery
Certification

Anchor
Skill-Requirements
Skill-Requirements
Types of Installation: Off-the-Floor, Floor-Based, Virtuoso, Wall Bed, Paxton, Martha Stewart

Installer Level Required: Jr. Apprentice Installer

Products Required: TFL Material, Accessories

Back to top

Anchor
Tools-&-Hardware
Tools-&-Hardware
Tools Required

Ceramic Scraper

Wax Crayon

System Cleaner

Rags

Hardware Required

Fast Caps

Back to top

Anchor
Installation-Steps
Installation-Steps
Process Steps

Panel
panelIconId1f9ba
panelIcon:safety_vest:
panelIconText🦺
bgColor#FFFAE6

Personal Protective Equipment (PPE) must beworn at all times when handling material and operating the power tools mentioned throughout this process. Review the PPE Matrix for further guidance.

  1. Identify areas of touch up.

Expand
titleClick for more information

  • Identify any scratches or markings made during the install.  For example, nail holes, screw holes, corners, scratches, etc.

  • If a piece of material is damaged or chipped in anyway that can not be easily touched up, report the piece to the shop/warehouse for replacement.

  1. Touch up dings and scratches.

Expand
titleClick for more information

  • Depending on the depth or size of a scratch, the part will either need to be replaced or can be touched up.

Touch

  • up

trim work

  • .

title
Expand

Click for visuals and more information
Image Removed

  1. Anchor
    Crayon
    Crayon
    Touch up using wax crayon.

Expand
titleClick for visuals and more information

  • When you notice any scratches, use the wax crayon that is the appropriate color and fill in the hole or groove.

  • Make sure to go over the spot enough times so the amount of crayon is taller than the hole you are filling.

  • Use a ceramic scraper and gently rub it across the wax to remove excess.

  • Using a dry rag, wipe the excess wax off the board and smooth out the repair.

  • Using system cleaner, wipe down the full piece of material.

  • If you wipe the area and the wax is no longer flush with the material, repeat the process to fill the hole.

  1. Touch up trim work.

Expand
titleClick for visuals and more information
Image Added

  1. Cover screws with fast caps.

Expand
titleClick for visuals and more information

  • For all screw holes created during installation, they should be countersunk.

  • If the screw sits proud of the board, the fast cap will not sit correctly.

  • Place the fast cap over the screw to cover the hole.  If the material contains grain, ensure the fast cap grain is following the board.

Click for visuals
Expand
title

Back to top

Anchor
Related-Training-Materials
Related-Training-Materials
Related Training Materials

Skeleton Fundamentals
Complete the Installation
Cleaning the System & Jobsite
Delivery to the Customer
PPE Matrix

Back to top

Anchor
Final-Steps-&-Delivery
Final-Steps-&-Delivery
Final Steps & Delivery

  1. If all touch ups have been completed, complete the clean up process.

  2. Complete the Professional Installation Experience by walking through the space with the customer and deliveringthe final product.

Back to top

Anchor
Certification-Steps
Certification-Steps

Panel
panelIconId270d
panelIcon:writing_hand:
panelIconText✍️
bgColor#E3FCEF

Certification Steps:

  1. All identified areas have been waxed or touched up using a marker.

  2. All excess wax or marker has been cleaned up and removed.

  3. All touched up areas blend in with the system and are not visible to the naked eye.

Back to top