Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Table of Contents
Apprentice to Journeyman Installer

Status
colourYellow
titleIN REVIEW
Anchor
Top
Top

This page explains the steps to take for installing hampers. Prior to beginning the installation, ensure you completed all steps of installing the system skeleton.

Page Contents

Skill Requirements
Tools & Hardware
Installation Steps
Related Training Materials
Final Steps & Delivery
Certification
Tips from the Field
BOM Codes


Anchor
Skill-Requirements
Skill-Requirements
Types of Installation: Floor-Based, Wall Bed

Installer Level Required: Apprentice Installer

Products Required: TFL Material, Accessories, Special Order

Back to top


Anchor
Tools-&-Hardware
Tools-&-Hardware
Tools Required

image-20240423-140025.png

Drill Driver/Impact Drill

image-20240423-140049.png

Phillips #2 Screwdriver

Back to top


Anchor
Installation-Steps
Installation-Steps
Installation Steps

Panel
panelIconId1f9ba
panelIcon:safety_vest:
panelIconText🦺
bgColor#FFFAE6

Personal Protective Equipment (PPE) must beworn at all times when handling material and operating the power tools mentioned throughout this process. Review the PPE Matrix for further guidance.

  1. Locate and inspect materials.

Expand
titleClick for more information
  • Ensure you have a hamper door, 2 hinges and 2 plates, 1 set of hamper arms.

    • Hamper arm set contains 2 hamper arms, 2 par brackets, and 2 door brackets.

  1. Attach the 2 hinge plates to the bottom shelf, and the 2 hinges to the door.

image-20240605-134328.png
image-20240701-131502.png

  1. Attach the door through the pre-drilled holes using provided screws.

  2. Install Lid Stay hardware.

Expand
titleClick for more information
  • Mount the partition mounting piece to the pre-drill holes of the partition using the included screws. This is the flat piece.

  • Mount the door face mounting piece to the pre-drilled holes on the door using the included screws. This is the piece with the 90-degree angle.

image-20240605-141827.pngImage Removed

image-20241025-202751.pngImage Addedimage-20241025-202826.pngImage Added

  • Once the door is mounted on the hinges, attach the lid stay arm to the lid stay hardware.

  • When the lid stay arms is closed, the large circle should be pointed to the back of the component.

  • Each side of the arm has an embossed arrow on the end; this arrow should align with the 90-degree angle of the plastic piece on the hardware.

    • The lid stay arm will snap into place once the arrow is aligned.

  1. Snap the hamper arms into the bracket on the partition.

Expand
titleClick for more information
  • Flip one arm around so one is pushing in and one is pushing out.

  1. Snap the door hinges into place by sliding the door in a downward motion.

  2. Connect the hamper arms to the door.

  3. Test the functionality by opening and closing the door several times.

  4. Adjust the hinges to align the door with above and adjacent doors and drawers. Ensure there are equal gaps when the door is closed.

  5. Install the hamper bag or basket.

Back to top


Anchor
Related-Training-Materials
Related-Training-Materials
Related Training Materials

Skeleton Fundamentals
Complete the Installation
System Touch Ups
Cleaning the System & Jobsite
Delivery to the Customer
PPE Matrix

Back to top


Anchor
Final-Steps-&-Delivery
Final-Steps-&-Delivery
Final Steps & Delivery

  1. Inspect the installation and complete any touch ups if necessary.

  2. If there are no more components to install, remove all stickers/labels.

  3. If there are no more components to install, complete the clean up process.

  4. If there are no more components to install, complete the Professional Installation Experience by walking through the space with the customer and deliveringthe final product.

Back to top


Anchor
Certification-Steps
Certification-Steps

Panel
panelIconId270d
panelIcon:writing_hand:
panelIconText✍️
bgColor#E3FCEF

Certification Steps:

  1. Hamper door opens and closes without rubbing or interfering with partition, door, or basket.

  2. Door is properly aligned on the cabinet with equal spacing around the perimeter.

  3. Door opens and closes with ease.

  4. Door opens far enough to allow bags or basket to come out.

  5. Stays are properly adjusted.

Back to top


Anchor
Tips
Tips
Tips from the Field
Tips submitted by fellow installers and leaders in the field. These optional tips are intended to make this install process simpler.

Panel
panelIconId1f5e3
panelIcon:speaking_head:
panelIconText🗣️
bgColor#DEEBFF

Click here to submit your own tip from the field.

Back to top


Anchor
BOM
BOM
BOM Codes
The purpose of this section is to provide guidance when confirming details on the BOM. This list includes all individual parts typically associated with this process.

BF

Hamper Bin Face

BFS

Hamper Bin Face Slab Only

HA

Hamper

HF

Hamper Face

HIN

Hinge

HL

Handle

HPI

Flip Up/Down Hardware

HWI

HH Flip Down Hardware

The codes in the table above are directly from the Corporate CAD database and may not reflect all codes included in the Supported Franchise Database or Independent Franchise Databases.

Back to top