Versions Compared

Version Old Version 15 New Version Current
Changes made by

Aleeshya Broome

Aleeshya Broome

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Table of Contents
Apprentice to Journeyman Installer

Status
colourGreen
titlelive
Anchor
Top
Top

This page explains the steps to take for installing a wrap panel. Prior to beginning the installation, ensure you completed all steps of hanging system rail and prepping partitions.

Page Contents

Skill Requirements
Tools & Hardware
Installation Steps
Related Training Materials
Final Steps & Delivery
Certification
Tips from the Field
Terms & Definitions
BOM Codes

Anchor
Skill-Requirements
Skill-Requirements
Types of Installation: Off-the-Floor, Floor-Based, Wall Bed

Installer Level Required: Apprentice Installer

Products Required: TFL Material

Back to top

Anchor
Tools-&-Hardware
Tools-&-Hardware
Tools Required

image-20231117-143249.png

Measuring Tape

image-20240223-144606.png

18-Gauge Nail Gun

Clamp

image-20240410-201353.png

Countersink Bit

Hardware Required

18-Gauge 1 1/4” Nails

18-Gauge 1 1/2” Nails

18-Gauge 2” Nails

image-20240410-201442.png

1 1/4” x #8 Screws

image-20240410-201442.png

1 5/8” x #8 Screws

image-20240410-201442.png

2” x #8 Screws

Back to top

Anchor
Installation-Steps
Installation-Steps
Installation Steps

Panel
panelIconId1f9ba
panelIcon:safety_vest:
panelIconText🦺
bgColor#FFFAE6

Personal Protective Equipment (PPE) must beworn at all times when handling material and operating the power tools mentioned throughout this process. Review the PPE Matrix for further guidance.

  1. Locate all materials.  Wrap panels can be single pieces or multiple pieces in a stack. 

If you are completing a multi-stack, pay close attention to the elevation to understand the orientation. If it is not clear, speak with the design consultant or your install manager for clarification.

  1. Dry fit the pieces to ensure all dimensions are correct and review where the attachment points are.  Note where all shelves are located on the partition.

  2. Beginning from the bottom, place the partition on top of the first wrap panel.

Expand
titleClick to view visuals and more information

  • Ensure there is no debris or anything between the panel and partition, and the partition is resting against the panel with no gaps.

  • A clamp will help to hold the panel in place.

  1. Attach the panel to the partition.

Expand
titleClick to view visuals and more information

  • Place a screw in the front and back of the partition at each fixed shelf location. All screws should be concealed by the shelf after it is installed. All screws must be countersunk.

  • Place nails in all corners of the partition aligning with the wrap panel, and every 18” along the front and back, continuing up the height of the partition.

  • Hide nails behind shelves or other elements of the component.

  • Refer to the table below to understand nail and screw sizes depending on the thickness of the material you are installing.

Material Thickness

Nail Size

Screw Size

3/4” partition or panel + 3/4” partition or panel

18-gauge 1 1/4”

1 1/4”

3/4” partition or panel + 1 1/8” partition or panel

18-gauge 1 1/2”

1 5/8”

1 1/8” partition or panel + 1 1/8” partition or panel

18-gauge 2”

2”

  1. Multi-Stack Only: Place the next panel under the partition and follow step 5 to secure it in place.

  2. Ensure all nail holes are touched up.

Back to top

Anchor
Related-Training-Materials
Related-Training-Materials
Related Training Materials

Skeleton Fundamentals
Complete the Installation
System Touch Ups
Cleaning the System & Jobsite
Delivery to the Customer
PPE Matrix
Product Feedback Form

Back to top

Anchor
Final-Steps-&-Delivery
Final-Steps-&-Delivery
Final Steps & Delivery

  1. Inspect the installation and complete any touch ups if necessary.

  2. If there are no more components to install, remove all stickers/labels.

  3. If there are no more components to install, complete the clean up process.

  4. If there are no more components to install, complete the Professional Installation Experience by walking through the space with the customer and deliveringthe final product.

Back to top

Anchor
Certification-Steps
Certification-Steps

Panel
panelIconId270d
panelIcon:writing_hand:
panelIconText✍️
bgColor#E3FCEF

Certification Steps:

  1. Panels are flush against the partition and secured with no gap.

  2. Screws are placed at each fixed shelf location and concealed by the fixed shelf.

  3. Nails are placed in each corner and every 12” - 18” along the front and back of the panel, continuing up the height of the component.

  4. Nails are hidden behind fixed and adjustable shelf locations.

  5. All nail holes have been touched up.

Back to top

Anchor
Tips
Tips
Tips from the Field
Tips submitted by fellow installers and leaders in the field. These optional tips are intended to make this install process simpler.

Panel
panelIconId1f5e3
panelIcon:speaking_head:
panelIconText🗣️
bgColor#DEEBFF

  • A wrap panel can be applied to the partition prior to hanging the partition. This is done on sawhorses.

Click here to submit your own tip from the field.

Back to top

Anchor
Terms
Terms
Terms & Definitions

BOM

Bill of Materials; Parts List

Elevation

The CAD Design Plan created by the Design Consultant with the client.

Dry Fit

Holding material or accessory in its intended location to test size accuracy.

Back to top

Anchor
BOM
BOM
BOM Codes
The purpose of this section is to provide guidance when confirming details on the BOM. This list includes all individual parts typically associated with this process.

BW

Backing Wrap Panel

EP

End Panel

PW

Partition Wrap Panel

The codes in the table above are directly from the Corporate CAD database and may not reflect all codes included in the Supported Franchise Database or Independent Franchise Databases.

Back to top