Page Comparison

Table of Contents
Journeyman to Senior Installer

The purpose of this page is to provide a comprehensive checklist for the full installation of a soft motion wall bed and a soft motion wall bed + desk. This checklist must be completed during every wall bed installation and uploaded to the corresponding job number in Dashboard.

A printable version is linked at the bottom of this page under Related Training Materials

Page Contents:

Job Information
Pre-Arrival Checklist
Photo Checklist
Rail/Partition
Cabinet Assembly
Top Shelf
Bottom Stretcher
Headboard
Toe Kick
Bed Frame Assembly
Bed Frame Attachment
Leg Adjustment
Top Stretcher
Lock
Mattress Installation
Finishing Touches
Related Training Materials

...

Date Inspected:  

Page numbers reference both the Soft Motion Wall Bed Installation Manual  (SMM) and the Wall Bed with Desk & Shelf (DSM) Installation Manual

...

• Check that the rail has not deformed or pulled away from the mounting surface / wall. 

• Check that the Suspension Bracket attachment screws are tight and not stripped (SMM & DSM: Page 4, Step 1). 

• Check that the suspension brackets are tight both up/down and in/out 

• Check that the partition is properly supported by the floor (using shims, par feet, etc.)  

...

• Partition mounting plate attachment to Partition 

  • Remove the Mechanism Cover to perform the following checks. 

  • Check that there are no open holes on the mounting plate (all attachment screws present). 

  • Check that all mounting plate attachment screws are tight and not stripped (SMM & DSM: Page 5, Step 3). 

  • Partition mounting plate should be tight to the partition (no gap) 

• Inspect top stretcher attachment 

  • Secure to the wall and not pulling away from the wall 

• Check that the cabinet has been leveled and plumbed. (Page 20SMM: Page 7, Step 7 | DSM: Page 8, Step 17) 

• Check that the cams are locked and the rafix bolts have not pulled out of the partition (SMM: Page 6, Step 2 | DSM: Page 7, Step 2). 

• Be sure the 3 angle brackets have been properly installed on the top of the top shelf into as many studs as possible (Page 21SMM: Page 28, Step 8 | DSM: Page 19, Step 7). 

• Ensure the anti-tip safety label has been affixed to the top shelf.

...

• Check that the bottom stretcher is tight against the wall or baseboard (SMM: Page 6, Step 3 | DSM: Page 7, Step 3). 

• Check that the bottom stretcher is attached to the partition using angle brackets (SMM: Page 6, Step 3 | DSM: Page 7, Step 3). 

• Be sure that the bottom stretcher is attached to as many studs as possible using screws specified in the Installation Instructions (SMM: Page 8, Step 8 | DSM: Page 9, Step 8) & (Page 20SMM: Page 27, Step 6 | DSM: Page 18, Step 35). 

• The stiffener has been installed on the headboard (SMM: Page 5, Step 5 | DSM: Page 6, Step 6) 

• Check that the cams on the headboard have been locked and the rafix bolts have not pulled out of the partition (SMM: Page 7, Steps 5 & 6 | DSM: Page 8, Steps 5 & 6). Do not use Press-In Cams. 

...

• Check that the toe kick is installed properly (attached to the partitions using angle brackets) (Page 7SMM: Page 8, Step 9 | DSM: Page 23, Step 76). 

• Check that there are no open holes and/or all required attachment points are properly secured (all attachment screws present). 

• Check that all bed frame attachment screws are tight and not stripped (Page 10SMM: Page 12, Step 2 | DSM: Page 11, Step 6a7). – use Allen wrench or screwdriver, not impact driver 

• Bed frame should be tight to the bed panels and squared to ensure the gap is equal to both partitions. 

• If the configuration has unsupported seams, check that mending plates have been used for support (Pages 12SMM: Pages 14-25 | DSM: Pages 14-15). 

• Check that the Steel Leg Spacer attachment screw is tight and not stripped (SMM: Page 1627, Step 24 | DSM: Pages 17 & 18). 

• Check that the Metal Washer has been used on the inside of the bed frame (SMM: Page 1731, Step 46 | DSM: Pages 17 & 18). 

• Check that the Plastic Washer is positioned between the Frame Mechanism and the Leg (SMM: Page 1728, Step 511 | DSM: Pages 26 & 27). 

• Check that the magnets are positioned correctly and are tight, but not stripped (Page 1930, Step 5 | Page 23, Step 5). 

• Check that the Sleeve Bearings have been used on the Frame Dowel and is properly seated in the U-Channel (SMM: Page 26, Step 1 | DSM: Page 16, Step 1). Be cautious not to crack sleeve bearings; if cracked, do not use (get a new one) 

• Check that the piston has been installed in the correct orientation (Page 17&18SMM: Page 29, Steps 1 & 2 | DSM: Page 21 & 22, Steps 1 & 2). – Ensure the correct size pistons have been used for the mattress (find chart) 

• Check that the piston mounts are properly seated on the welded pins (Page 17&18SMM: Page 29, Steps 1 & 2 | DSM: Page 21 & 22, Steps 1 & 2). 

• Check that the Top Steel Stretcher Screws are tight and not stripped (Page 18SMM: Page 30, Step 4 | DSM: Page 23, Step 34). 

• Check that the Magnets are properly contacting the Top Steel Stretcher when closing the bed (Page 19SMM: Page 29, Step 2 | DSM: Page 22, Step 52). 

• When opening and closing bed make sure motion is not restricted 

...

• Be sure both feet on each leg are touching the floor. If not, adjust the Cam Washer accordingly (Page 1931, Step 6 | Page 25, Step 58). 

• Check all attachment screws for the Leg Mechanism are tight and not stripped (Page 1931, Step 6 | Page 25, Step 58)

• Ensure the pinch hazard safety label has been affixed to the right or left leg. 

...

• Check that the top stretcher is tight against the wall (Page 208, Step 11 | Page 9, Step 411). 

• Check that the top stretcher is tight to the top shelf and is tight and square to both partitions (Page 2027, Step 7 | Page 19, Step 46). 

• Check that the top stretcher is attached to as many studs as possible using screws specified in the Installation Instructions (Page 20Page 27, Step 7 | Page 19, Step 46). 

...

• Check that the Mattress Hard Stops are installed properly (Page 20SMM: Page 32, Step 7 | DSM: Page 29, Step 51). 

• Check that the Mattress is secured down using straps connected to the frame (Page 21, Step 13).  

• Test pull down/push up mechanism of system 

• Re-install pistons (if they were removed). 

• Re-attach the Mechanism Cover using all mounting screws. Ensure screws are tight and not stripped (Page 21SMM: Page 32, Step 8 | DSM: Page 29, Step 62). 

• Re-install Top Steel Stretcher (if removed). 

• Double check safety labels are in their correct places.

• Ensure all safety check photos have been taken.

• Provide the mattress set up document to the customer and advise they wait 48 hours to allow the mattress to inflate before use.

• Checklist uploaded to Dashboard

Inspection Complete Signoff: 

...

Soft Motion Wall Bed Installation Manual
Soft Motion Wall Bed + Desk Installation Manual
Download Checklist for Printing
Product Feedback Form

Back to top

...