Versions Compared

Version Old Version 8 New Version Current
Changes made by

Aleeshya Broome

Aleeshya Broome

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Table of Contents
Journeyman to Senior Installer

Status
colourYellow
titlein review
Anchor
Top
Top

The purpose of this page is to outline the process steps of installing a modesty panel. A modesty panel services 2 key purposes: (1) It creates a blocked view of what is under a countertop; (2) It acts as a support. Prior to beginning this process, ensure the section or cabinet is built that will contain the modesty panel.

Page Contents

Skill Requirements
Tools & Hardware
Installation Steps
Related Training Materials
Final Steps & Delivery
Certification
Tips from the Field
Terms & Definitions
BOM Codes

Anchor
Skill-Requirements
Skill-Requirements
Types of Installation: Floor-Based

Installer Level Required: Journeyman Installer

Products Required: TFL Material, Special Order

Back to top

Anchor
Tools-&-Hardware
Tools-&-Hardware
Tools Required

image-20240619-164739.png

Screw Driver

image-20240619-164754.png

Drill Driver/Impact Drill

image-20240619-165031.png

Adjustable Square

image-20240702-130947.png

3/16” Drill Bit

Hardware Required

image-20240619-164858.png

Rafix Pins

image-20240619-164915.png

L Brackets

image-20240619-164930.png

3/4” Panhead Screws

Back to top

Anchor
Installation-Steps
Installation-Steps
Installation Steps

Panel
panelIconId1f9ba
panelIcon:safety_vest:
panelIconText🦺
bgColor#FFFAE6

Personal Protective Equipment (PPE) must beworn at all times when handling material and operating the power tools mentioned throughout this process. Review the PPE Matrix for further guidance.

  1. Drill for Rafix pins on the attaching partitions or shelves.  Insert the pins.

Expand
titleClick for more information

  • Use an adjustable square to measure 3/8” up from the bottom, and mark across your center line.

  • With a 3/16” bit, drill a hole 5/8” deep on the mark just made on the face of the shelf.

  • Be careful not to make the hole larger than it should be.

  • Clean any pencil marks and screw in Rafix pins.

Ensure all cams, mending plates, L brackets, etc. are on the inside of the build and not visible from the outside.  All seams are to be tight with no gaps.

  1. Place the panel in its intended position.

Expand
titleClick for more information

  • If the panel is not the same height as the part it is connecting to, align it to be flush to the top of the panel it is connecting to.

  1. Once the modesty panel is in place, tighten the cams with a screw driver.

  2. If Applicable: Affix the L bracket to the modest modesty panel and the adjacent panel.

Expand
titleClick for more information

  • These L brackets will serve as attachment points for the countertop above the panel.

  1. If Applicable: Install the countertop and secure the modest panel to the countertop with the L brackets. 

Back to top

Anchor
Related-Training-Materials
Related-Training-Materials
Related Training Materials

Skeleton Fundamentals
Complete the Installation
System Touch Ups
Cleaning the System & Jobsite
Delivery to the Customer
PPE Matrix
Product Feedback Form

Back to top

Anchor
Final-Steps-&-Delivery
Final-Steps-&-Delivery
Final Steps & Delivery

  1. Inspect the installation and complete any touch ups if necessary.

  2. If there are no more components to install, remove all stickers/labels.

  3. If there are no more components to install, complete the clean up process.

  4. If there are no more components to install, complete the Professional Installation Experience by walking through the space with the customer and deliveringthe final product.

Back to top

Anchor
Certification-Steps
Certification-Steps

Panel
panelIconId270d
panelIcon:writing_hand:
panelIconText✍️
bgColor#E3FCEF

Certification Steps:

  1. Modesty panel is secure with no gaps.

  2. There are no securement points visible.

Back to top

Anchor
Tips
Tips
Tips from the Field
Tips submitted by fellow installers and leaders in the field. These optional tips are intended to make this install process simpler.

Panel
panelIconId1f5e3
panelIcon:speaking_head:
panelIconText🗣️
bgColor#DEEBFF

Click here to submit your own tip from the field.

Back to top

Anchor
Terms
Terms
Terms & Definitions

BOM

Bill of Materials; parts list

Back to top

Anchor
BOM
BOM
BOM Codes
The purpose of this section is to provide guidance when confirming details on the BOM. This list includes all individual parts typically associated with this process.

MP

Modesty Panel

MPB

Modesty Panel Bracket

TMP

Table Modesty Panel

The codes in the table above are directly from the Corporate CAD database and may not reflect all codes included in the Supported Franchise Database or Independent Franchise Databases.

Back to top