...
Read through Soft Motion Wall Bed Installation Manual
Watch all Wall Bed Installation Videos on CC360 share
Read and understand the Wall Bed inspection checklist
Make sure to have the following items with you for each site visit inspection:
Printed copy of the Soft Motion Wall Bed Installation Manual
Required tools (Page 2)
Non-supplier hardware (Page 3)
(5) 1x1 angle brackets
(1) New piece of rail and cover
(1) Top Stretcher
(1) Bottom Stretcher
(1) New Toe Kick
Additional hardware kits
Leg kits
Full bed kit Wall Bed Hardware Kit: An extra kit of all brackets and hardware pieces for installation
| Anchor | ||||
|---|---|---|---|---|
|
Legs (both sides of bed)
Mounting Plate (Both Sides)
Overall picture of the unit (closed)
Overall picture of the unit (open)
Close up of top shelf with angle brackets
Close up of Top Stretcher with Screw Caps visible
Close up of Bottom Stretcher with Screw Caps and Angle Brackets visible
Close up of toe kick with Angle Brackets visible
Close up of lock engagement on both partitions (only Desk/Shelf versionWall Bed + Desk only)
Lighting (drivers/distribution boxes)
Safety stickers attached to system
...
Inspect vendor supplied components
Inspect the shipment impact sensor. If the sensor has been triggered, inspect the full wall bed frame and ensure it is square for installation. If it is not square, report the damage to your manager; they can assist with re-ordering if necessary.
Partition mounting plate
Bending or twisting (welded pin or mounting plate)
Bed Frame
Welded pin on bed frame (both sides)
Ensure square
| Anchor | ||||
|---|---|---|---|---|
|
...
Check that the cams are locked and the rafix bolts have not pulled out of the partition (Page 6, Step 2).
Be sure that the 3 angle brackets have been properly installed on the top of the top shelf into as many studs as possible (Page 21, Step 7).
Ensure the anti-tip safety label has been affixed to the top shelf.
...
| Anchor | ||||
|---|---|---|---|---|
|
...
Check that there are no open holes on bed frame based on type of door being used and/or all required attachment points are properly secured (all attachment screws present).
Check that all bed frame attachment screws are tight and not stripped (Page 10, Step 6a). – use Allen wrench or screwdriver, not impact driver
Bed frame should be tight to the bed panels and squared to ensure the gap is equal to both partitions.
If the configuration has unsupported seams, check that mending plates have been used for support (Pages 12-15).
Check that the Steel Leg Spacer attachment screw is tight and not stripped (Page 16, Step 2).
Check that the Metal Washer has been used on the inside of the bed frame (Page 17, Step 4).
Check that the Plastic Washer is positioned between the Frame Mechanism and the Leg (Page 17, Step 5).
Check that the magnets are positioned correctly and are tight, but not stripped (Page 19, Step 5).
...
Be sure both feet on each leg are touching the floor. If not, adjust the Cam Washer accordingly (Page 19, Step 5).
Check all attachment screws for the Leg Mechanism are tight and not stripped (Page 19, Step 5)
Ensure the pinch hazard safety label has been affixed to the right or left leg.
...
| Anchor | ||||
|---|---|---|---|---|
|
Check that the top stretcher is tight against the wall (Page 20, Step 4).
Check that the top stretcher is tight to the top shelf and is tight and square to both partitions (Page 20, Step 4).
Check that the top stretcher is attached to as many studs as possible using screws specified in the Installation Instructions (Page 20, Step 4).
| Anchor | ||||
|---|---|---|---|---|
|
...
(Wall Bed + Shelf Only)
Ensure that the lock fully engages on both partitions and moves easily into locked position. Ensure no bending of locking bar.
...
Test pull down/push up mechanism of system
Re-install pistons (if they were removed).
Re-attach the Mechanism Cover using all mounting screws. Ensure screws are tight and not stripped (Page 21, Step 6).
Re-install Top Steel Stretcher (if removed).
Double check safety labels are in their correct places.
Ensure all safety check photos have been taken.
Inspection Complete Signoff:
...
| Anchor | ||||
|---|---|---|---|---|
|
Soft Motion Wall Bed Installation Manual
Soft Motion Wall Bed + Desk Installation Manual
...