Versions Compared

Version Old Version 12 New Version 13
Changes made by

Aleeshya Broome

Aleeshya Broome

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Status
colourGreen
titleLIVE
Anchor
Top
Top

This page explains the process for installing a floor-based system. The steps below outline the order of preparing and leveling the skeleton, and supporting the system on the floor.

Page Contents

Skill Requirements
Tools & Hardware
Installation Steps
Related Training Materials
Next Steps
Certification
Tips from the Field
Terms & Definitions

Anchor
Skill-Requirements
Skill-Requirements
Types of Installation: Floor-Based

Installer Level Required: Journeyman Installer

Products Required: TFL Material, Accessories, Special Order

Back to top

Anchor
Tools-&-Hardware
Tools-&-Hardware
Tools Required

Drill Driver/Impact Drill

4' Level

Step Ladder

Hammer

Par Feet (Option 1)

Shims (Option 2)

Hardware Required

3/4” x #8 Screws

Back to top

Anchor
Installation-Steps
Installation-Steps
Installation Steps

Panel
panelIconId1f9ba
panelIcon:safety_vest:
panelIconText🦺
bgColor#FFFAE6

Personal Protective Equipment (PPE) must beworn at all times when handling material and operating the power tools mentioned throughout this process. Review the PPE Matrix for further guidance.

  1. Remove baseboards (if applicable) for all areas located behind a system.

Expand
titleClick for visuals and more information

  • Do not remove baseboards unless indicated on the elevation or approved by the customer.

  • Prior to removal, cut caulk line.

  • Using a hammer and pry bar, start prying baseboard away from the wall.  Pry at stud locations to minimize drywall damage. Ensure you have a putty knife placed behind the pry bar to support the force between the bar and the wall.

  • Try to start removal in an area that will be concealed if any wall damage is done.

If baseboards are not being removed, notch partitions based on baseboard size and elevation measurements (if applicable).

  1. Ensure you have checked for the high point in the space.

  2. Hang system rail according to floor-based process steps.

  3. Prepare and hang partitions. If using par feet for support, attach par feet during this step.

  4. Install top, middle and bottom fixed shelves.

  5. Level system from the high spot in the room. Slide your level across the top of the system and adjust the partition suspension brackets accordingly.

Expand
titleClick for visuals and more information

  • Lower the partition to the ground at the high point and level the remainder of the system.

image-20231116-211836.png

  1. Plumb the system from left to right using a 2 or 4-foot level to ensure it is square.

Expand
titleClick for more information

  • Place a 2 or 4-foot level on the front of each partition.

  • Use the adjustment screw on the suspension bracket until the horizontal bubble is centered on the level.

  • Place a 2 or 4-foot level on the side of each partition.

  • Move the bottom of the partition left or right until the horizontal bubble is centered on the level.

    • If there is a wall on either side of the system preventing you from placing a level, plumb the system from the inside of the partitions.

    • If there are fixed shelves preventing you from placing a level, remove any applicable shelves.

If partitions are longer than 6 feet, check for levelness in two spots: high and low.

  1. Secure corner brackets to the wall.

Expand
titleClick for more information

  • Use a stud finder and skim across the wall where the corner brackets sit to see if there are studs.

    • If there is a stud: Use a 2.5” screw and secure the bracket to the wall.

    • If there is no stud: Mark the location, pre-drill a hole through the corner bracket using a 3/16” bit, and install a metal EZ anchor through the corner bracket into the hole.

  1. Close the corner bracket caps.

Expand
titleClick for visuals and more information

  • When everything is secure, close all caps and press firmly to ensure they are closed.

  • If the corner bracket does not close, create a slight bend in the cap using your finger.

IMG_62571-ezgif.com-video-to-gif-converter.gif

  1. If using shims for support, place them under the front and back of each partition.

Expand
titleClick for visuals and more information

  • Ensure they are flush or inset half of the partition width if visible.

Back to top

Anchor
Related-Training-Materials
Related-Training-Materials
Related Training Materials

Skeleton Fundamentals
PPE Matrix

Back to top

Anchor
Final-Steps-&-Delivery
Final-Steps-&-Delivery
Next Steps:

Complete the Installation
System Touch Ups
Cleaning the System & Jobsite
Delivery to the Customer
PPE Matrix

Back to top

Anchor
Certification-Steps
Certification-Steps

Panel
panelIconId270d
panelIcon:writing_hand:
panelIconText✍️
bgColor#E3FCEF

Certification Steps:

  1. System rail is hung according to the height of the partition and high point of the space.

  2. Shims or par feet are used for support under the front and back of the partitions.

  3. If applicable: Baseboards have been removed cleanly or partitions have been notched.

  4. Partitions are secured to the wall.

Back to top

Anchor
Tips
Tips
Tips from the Field
Tips submitted by fellow installers and leaders in the field. These optional tips are intended to make this install process simpler.

Panel
panelIconId1f5e3
panelIcon:speaking_head:
panelIconText🗣️
bgColor#DEEBFF

Click here to submit your own tip from the field.

Back to top

Anchor
Terms-&-Definitions
Terms-&-Definitions
Terms & Definitions

Elevation

The CAD Design Plan created by the Design Consultant with the client.

Level

The wall or system is horizontally straight.

Plumb

The wall or system is vertically straight.

Back to top