Versions Compared

Version Old Version 6 New Version Current
Changes made by

Aleeshya Broome

Aleeshya Broome

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Table of Contents
Journeyman to Senior Installer

Status
colourYellow
titlein review
Anchor
Top
Top

The purpose of this page is to outline the process steps for installing automatic wardrobe lifts. Prior to beginning this process, ensure the system skeleton is complete.

Page Contents

Skill Requirements
Tools & Hardware
Installation Steps
Related Training Materials
Final Steps & Delivery
Certification
Tips from the Field
Terms & Definitions
BOM Codes

Anchor
Skill-Requirements
Skill-Requirements
Types of Installation: Off-the-Floor, Floor-Based

Installer Level Required: Journeyman Installer

Products Required: Special Order

Back to top

Anchor
Tools-&-Hardware
Tools-&-Hardware
Tools Required

image-20240619-153253.png

StorageMotion Installation Instructions

image-20240702-130543.png

Cable Clips
(Optional)

image-20240702-130621.png

Cable Grommet

Back to top

Anchor
Installation-Steps
Installation-Steps
Installation Steps

Panel
panelIconId1f9ba
panelIcon:safety_vest:
panelIconText🦺
bgColor#FFFAE6

Personal Protective Equipment (PPE) must beworn at all times when handling material and operating the power tools mentioned throughout this process. Review the PPE Matrix for further guidance.

  1. Ensure the pole is cut to the correct size prior to leaving the shop/warehouse. The size is indicated on the elevation.

  2. Open the box and ensure all parts are included.

  3. Measure the pole to ensure it is the right size for the component.

  4. Follow the instructions provided.

Expand
titleTips for a successful installation

  • Make sure the steel motor tube is cut to the proper length (-1.5” less than section width) before going to the job site.

  • Install the motor tube and pivot arms at the proper heights/depths to prevent any binding issues.

    • Start out by marking the height of the motor tube location to be 1-2” from the underside of the top shelf.

      • 2” to center will allow maximum hanging height

      • This will determine the height to mount the rotating arms.

    • Install the rotating arms approx. 9” from the back of the pars-(will be close to flush to front of 14”d pars),

      • while maintaining 1.5-3” from the clothes pole (center to center) below where the motor tube will be.

    • Install the motor tube and straps about 6” behind the rotating arms (near the back wall).

  • Power source is required.

    • May need cable clips to secure the power cord to back underside of the top shelf (depending on power source location)

    • Power cord must be on the left side of the motor tube.

    • Grommet as needed to allow cord to plug in. 

Disregard the wood box in photo 9 and 10 as we have never built those to cover the motor tube, the tube is paintable.

  1. Check to ensure everything is functioning as intended.

  2. Upon the final walkthrough with the customer, spend an extra moment teaching the customer how to use the new lift.

Expand

  • Show them how to operate the lift and ask them to demonstrate so they feel comfortable.

  • Answer any questions the customer may have.

Back to top

Anchor
Related-Training-Materials
Related-Training-Materials
Related Training Materials

StorageMotion Installation Manual
Skeleton Fundamentals
Complete the Installation
System Touch Ups
Cleaning the System & Jobsite
Delivery to the Customer
PPE Matrix
Product Feedback Form

Back to top

Anchor
Final-Steps-&-Delivery
Final-Steps-&-Delivery
Final Steps & Delivery

  1. Inspect the installation and complete any touch ups if necessary.

  2. If there are no more components to install, remove all stickers/labels.

  3. If there are no more components to install, complete the clean up process.

  4. If there are no more components to install, complete the Professional Installation Experience by walking through the space with the customer and deliveringthe final product.

Back to top

Anchor
Certification-Steps
Certification-Steps

Panel
panelIconId270d
panelIcon:writing_hand:
panelIconText✍️
bgColor#E3FCEF

Certification Steps:

  1. Lift is installed in the correct spot indicated on the elevation.

  2. Lift is functioning correctly.

  3. Lift is demonstrated to the customer during the final walkthrough.

Back to top

Anchor
Tips
Tips
Tips from the Field
Tips submitted by fellow installers and leaders in the field. These optional tips are intended to make this install process simpler.

Panel
panelIconId1f5e3
panelIcon:speaking_head:
panelIconText🗣️
bgColor#DEEBFF

Click here to submit your own tip from the field.

Back to top

Anchor
Terms
Terms
Terms & Definitions

BOM

Bill of Materials; parts list

Elevation

The CAD Design Plan created by the Design Consultant with the client.

Back to top

Anchor
BOM
BOM
BOM Codes
The purpose of this section is to provide guidance when confirming details on the BOM. This list includes all individual parts typically associated with this process.

AWDL

Auto Wardrobe Lift

Text Note

Wardrobe Lift Extended Arm

WDL

Wardrobe Lift

The codes in the table above are directly from the Corporate CAD database and may not reflect all codes included in the Supported Franchise Database or Independent Franchise Databases.

Back to top