Table of Contents
Journeyman to Senior Installer
| Status | ||||
|---|---|---|---|---|
|
| Anchor | ||||
|---|---|---|---|---|
|
The purpose of this page is to outline to process of installing or attaching multiple office accessories, including magnetic marker boards and fabric/tack boards. If you are installing a non-magnetic marker board, review the press-in panel instructions.
Page Contents
Skill Requirements
Tools & Hardware
Installation Steps
Marker Boards
Tack Boards
Related Training Materials
Final Steps & Delivery
Certification
Tips from the Field
Terms & Definitions
BOM Codes
| Anchor | ||||
|---|---|---|---|---|
|
Installer Level Required: Journeyman Installer
Products Required: Accessories, Special Order
| Anchor | ||||
|---|---|---|---|---|
|
Drill Driver/Impact Drill
Tape Measure
1/2” Drill Bit
18-Gauge Nail Gun
Liquid Nails
4' Level
Stud Finder
Hardware Required
18-Gauge 1 1/4” Nails
Toggle Bolts
2 1/2” Screws
| Anchor | ||||
|---|---|---|---|---|
|
| Panel | ||||||||
|---|---|---|---|---|---|---|---|---|
| ||||||||
Personal Protective Equipment (PPE) must beworn at all times when handling material and operating the power tools mentioned throughout this process. Review the PPE Matrix for further guidance. |
Marker Boards
| Anchor | ||||
|---|---|---|---|---|
|
Determine the height of the board based on the elevation. If this is not noted, reach out to the design consultant.
On the board, measure from top of the panel down to the center of the pre-drilled hole in the bottom track. Note this measurement.
Repeat this measurement for bottom bottom track. Note this measurement.
Remove tape to separate the pieces of the Z cleat and remove bottom track
Measure from floor to indicated height of accessory
Transfer both cleat marks to the wall.
Draw a level line for both bottom cleats.
Place the bottom cleat on the wall, with the line centered on the holes.
Determine location of studs for securement points. Drill for any toggles using a 1/2” drill bit.
All holes on the cleat should be used for securement. At least 2 studs should be hit for securement.
Secure using 2.5” screws and toggles through all holes on the bottom cleats.
Hook the board onto the bottom cleats.
Fabric/Tack Boards
| Anchor | ||||
|---|---|---|---|---|
|
Complete the full installation of the adjacent or surrounding system.
Measure the area to ensure the tack board will fit.
Place circle of liquid nails on the back of the tack board.
Place the tack board on the wall.
Secure in place using 1 1/4” nails. Ensure they sit below the fabric so they are not seen.
| Anchor | ||||
|---|---|---|---|---|
|
Skeleton Fundamentals
Complete the Installation
System Touch Ups
Cleaning the System & Jobsite
Delivery to the Customer
PPE Matrix
Product Feedback Form
| Anchor | ||||
|---|---|---|---|---|
|
Inspect the installation and complete any touch ups if necessary.
If there are no more components to install, remove all stickers/labels.
If there are no more components to install, complete the clean up process.
If there are no more components to install, complete the Professional Installation Experience by walking through the space with the customer and deliveringthe final product.
| Anchor | ||||
|---|---|---|---|---|
|
| Panel | ||||||||
|---|---|---|---|---|---|---|---|---|
| ||||||||
Certification Steps: |
| Anchor | ||||
|---|---|---|---|---|
|
Tips submitted by fellow installers and leaders in the field. These optional tips are intended to make this install process simpler.
| Panel | ||||||||
|---|---|---|---|---|---|---|---|---|
| ||||||||
Click here to submit your own tip from the field.
| Anchor | ||||
|---|---|---|---|---|
|
BOM | Bill of Materials; parts list |
| Anchor | ||||
|---|---|---|---|---|
|
The purpose of this section is to provide guidance when confirming details on the BOM. This list includes all individual parts typically associated with this process.
Text Note | Standardized Magnetic Markerboard |
Text Note | Leather Desk Blotter |
The codes in the table above are directly from the Corporate CAD database and may not reflect all codes included in the Supported Franchise Database or Independent Franchise Databases.