Office Accessories: Desk

Table of Contents
Journeyman to Senior Installer

IN REVIEW

The purpose of this page is to outline instructions and considerations when installing all items related to a desk or home office set up.

Page Contents

Types of Installation: Floor-Based, Wall Bed

Installer Level Required: Journeyman Installer

Products Required: TFL Material, Accessories, Special Order

Tools Required

Open

Drill Driver/Impact Drill

Open

Tape Measure

 

Hardware Required

Instructions & Considerations

Acrylic Dividers

If the accessory is a tray: Place the tray in its indicated location, as noted on the elevation.

If the accessory is being placed in a drawer:

1. If Provided: Place the bottom pad in place.

2. Place the horizontal and vertical dividers in their indicated orientation.

   1. If the dividers are only front-to-back, adhere the divider slides to the front and back from the drawer box. Slide the dividers into the slots.

Blotter

1. Place in position according to the text note on the elevation.

2. Ensure it is correct side up (texture/design side facing up).

3. Explain to the customer they can clean the blotter with a slightly damp cloth, or a standard shoe polish for surface scratches/marks.

Deluxe Sit-To-Stand 

Refer to the instructions provided by Richelieu

Considerations:

• Using the provided instructions, confirm you have all parts and pieces

• The table base should be centered on the countertop.

• Leave a minimum 0.5” overhang from the side edge to the leg frame.

• Refer to pages 6 and 7 in the Richelieu manual (linked above) for programming instructions.

• Programming notes should be included from the designer. If they are not:

  • Program 1: 30”

  • Program 2: 36”

  • Program 3: 42”

  • Program 4: 48”

• Leave programming instructions with the customer for future modifications.

Double Monitor Arm

Clamp-Mount: Refer to the instructions provided by Richelieu

In-Surface Instructions to be sent from Richelieu

Considerations:

• Using the provided instructions, confirm you have all parts and pieces

• The clamp-mount arm cannot be installed in the following situations. Contact the design consultant if you encounter any of these:

  • Sit-to-stand desk with modesty panel.

  • Peninsula/Island with a flush modesty panel.

  • Countertop immediately against the wall.

• Demonstrate the adjustability to the customer.

• California Closets does not install monitors to monitor arms.

File Drawer

1. Install the drawer according to standard process.

2. Demonstrate the file drawer system and its adjustability to the customer and, if applicable, encourage them to place a file folder inside.

Keyboard Tray

Refer to the instructions provided by Richelieu

Considerations:

• Using the provided instructions, confirm you have all parts and pieces

• Use the template and screws provided.

• Refer to engineering drawings for attachment locations:

  • Compadre Keyboard Tray

  • Momentum Keyboard Arm

• If the mounting location is not indicated on the elevation, contact the Design Consultant.

Mini Pencil Drawer

Refer to the instructions provided by Richelieu

Considerations:

• If the mounting location is not indicated on the elevation, contact the Design Consultant.

Single Monitor Arm

Clamp-Mount: Refer to the instructions provided by Richelieu

In-Surface Instructions to be sent from Richelieu (coming)

Considerations:

• Using the provided instructions, confirm you have all parts and pieces

• The clamp-mount arm cannot be installed in the following situations. Contact the design consultant if you encounter any of these:

  • Sit-to-stand desk with modesty panel.

  • Peninsula/Island with a flush modesty panel.

  • Countertop immediately against the wall.

• Demonstrate the adjustability to the customer.

• California Closets does not install monitors to monitor arms.

Sit-To-Stand Workstation

Refer to the instructions provided by Richelieu

1. Using the provided instructions, confirm you have all parts and pieces

2. If Applicable: Assemble pieces out of the box.

3. Place on the desk in the location indicated on the elevation.

4. Place the cable wrap on the desk for the customer to use.

5. Demonstrate how to use the cable wrap to the customer.

6. Demonstrate lifting and lowering the workstation.

7. Leave instructions behind for the customer’s use.

Standard Sit-To-Stand      

Refer to the instructions provided by Richelieu

Considerations:

• Using the provided instructions, confirm you have all parts and pieces

• The table base should be centered on the countertop.

• Leave a minimum 0.5” overhang from the side edge to the leg frame.

Table Legs

1. Using the provided instructions, confirm you have all parts and pieces

2. Place the countertop top side down on the floor. Use a drop cloth to protect the countertop.

3. Place legs in position on bottom of countertop

4. Mount using 3/4” screw and, if applicable, 1/4” washer

   1. Round/Square Table Legs: Secure through all holes

   2. X-Shaped Table Legs: Secure through at least 4 holes

   3. U-Shaped Table Legs: Secure through all holes

5. Unless otherwise indicated on the elevation, secure each table leg 3” from edge on center.

Related Training Materials

Skeleton Fundamentals
Complete the Installation
System Touch Ups
Cleaning the System & Jobsite
Delivery to the Customer
PPE Matrix
Product Feedback Form

Final Steps & Delivery

1. Inspect the installation and complete any touch ups if necessary.

2. If there are no more components to install, remove all stickers/labels.

3. If there are no more components to install, complete the clean up process.

4. If there are no more components to install, complete the Professional Installation Experience by walking through the space with the customer and delivering the final product.

Tips from the Field
Tips submitted by fellow installers and leaders in the field. These optional tips are intended to make this install process simpler.

Click here to submit your own tip from the field.

Terms & Definitions

BOM Codes
The purpose of this section is to provide guidance when confirming details on the BOM. This list includes all individual parts typically associated with this process.

The codes in the table above are directly from the Corporate CAD database and may not reflect all codes included in the Supported Franchise Database or Independent Franchise Databases.