/
Locks

Locks

Owned by Aleeshya Broome, created
Last updated: Jan 17, 2025
6 min read

Table of Contents
Journeyman to Senior Installer

in review

The purpose of this page is to outline the process of installing a standard lock and a stealth lock. Prior to completing this process, ensure the remainder of the installation is completed for the component(s) containing the lock.

 

Page Contents

Skill Requirements
Tools & Hardware
Installation Steps
Standard Lock
Stealth Lock
Related Training Materials
Final Steps & Delivery
Certification
Tips from the Field
Terms & Definitions
BOM Codes

Types of Installation: Off-the-Floor, Floor-Based, Wall Bed

Installer Level Required: Journeyman Installer

Products Required: Accessories, Special Order

Back to top

Tools Required

image-20240620-153747.png

Pliers

image-20240620-153801.png

Multi-Tool

Tape Measure

Socket Wrench

Pencil

 

 

Back to top

Installation Steps

Personal Protective Equipment (PPE) must be worn at all times when handling material and operating the power tools mentioned throughout this process. Review the PPE Matrix for further guidance.

Standard Lock

  1. Determine if the door or drawer needs to be drilled for the lock.

  • Once the drawer/door is in place, make markings for drilling the lock. Take into consideration:

    • Does the lock strike fit into any slots that have been routed?

    • Does the lock fit into any hardware that has been mounted on the back of any multi-door section?

    • Will the lock interfere with anything (shelf, accessory, handle, etc.)?

    • If the lock is on a single cabinet, does the rotation of the lock need to go in a certain direction?

    • Do you have any elbow catches going in multi-door sections?

  1. If Applicable: Drill out the holes to install the lock.

  2. Install the lock.

  • Pay attention to the way the lock strike turns in order to mount the lock base correctly.

  • Mount any applicable hardware on the adjacent door.

  • Install any applicable elbow catches.

    • Mount one half to the door and the other half must be mounted to a fixed shelf.

  • Refer to the elevation and determine if any locks are to share the same key.

    • This will determine if the correct locks are in the correct location.

  1. Ensure functionality of the lock.

  • Close all doors and drawers.

  • Using the provided key, lock and unlock each lock.

    • Repeat this process once or twice.

  • If adjustments are needed for fit, use a pair of pliers and bend the lock strike gently so it fits in the slot.

  1. Complete the final walkthrough with the customer and demonstrate the lock and provide the key to the customer.

 

Stealth Lock

  1. Unpackage the lock.

  • Make sure the red plastic guide is attached to the lock body.

  • The small piece (lock hook) that connects to the drawer face should be connected to the red plastic guide as well.

  • Ensure you have at least 1 remote. You cannot install the lock if you do not have a remote.

    • Contact your manager if you do not have the remote.

  1. Remove the drawer to ensure an open work space.

  2. Find the center of the fixed shelf that is above the drawer and make a small pencil mark.

  3. Hold the lock assembly up to the bottom of the shelf and line up the mark with the center line that is on the lock.

  1. Using the provided screws, secure the lock in place.

  2. Re-install the drawer removed during step 2.

  3. Peel the adhesive backer off of the piece connecting to the drawer.

  4. Close the drawer and give an extra push on the face where the lock hook connects to it.

  5. Open the drawer. The lock hook should be stuck to the inside of the drawer face. Secure the lock hook.

  1. With the drawer still open, remove the red plastic piece and discard it.

  2. Reach into the drawer and remove the battery cover off of the lock and insert the batteries. Place the battery cover on the lock.

  3. Ensure the lock functions.

  1. Complete the final walkthrough with the customer and demonstrate the lock and its electronic requirements.

 

Back to top

Related Training Materials

Skeleton Fundamentals
Complete the Installation
System Touch Ups
Cleaning the System & Jobsite
Delivery to the Customer
PPE Matrix
Product Feedback Form

Back to top

Final Steps & Delivery

  1. Inspect the installation and complete any touch ups if necessary.

  2. If there are no more components to install, remove all stickers/labels.

  3. If there are no more components to install, complete the clean up process.

  4. If there are no more components to install, complete the Professional Installation Experience by walking through the space with the customer and delivering the final product.

Back to top

Certification Steps:

  1. The lock is installed in the correct location according to the elevation.

  2. The lock functions to lock and unlock the cabinet.

Back to top

Tips from the Field
Tips submitted by fellow installers and leaders in the field. These optional tips are intended to make this install process simpler.

  • Clamp a piece of scrap material to the back of the door/drawer when drilling for the lock. This will help prevent chipping on the backside of the material.

Click here to submit your own tip from the field.

Back to top

Terms & Definitions

BOM

Bill of Materials; parts list

Elevation

The CAD Design Plan created by the Design Consultant with the client.

Back to top

BOM Codes
The purpose of this section is to provide guidance when confirming details on the BOM. This list includes all individual parts typically associated with this process.

LK

Face Lock

Text Note

Safe & Stealth Lock Parts

The codes in the table above are directly from the Corporate CAD database and may not reflect all codes included in the Supported Franchise Database or Independent Franchise Databases.

Back to top

Questions? Please e-mail Aleeshya Broome (albroome@calclosets.com)